Lessons

AIR GOONS NAVIGATION COURSE - DON'T BE A WAYPOINT CRIPPLE

Goofus flies in the general direction of the target, wasting time and fuel when he gets lost.

Gallant flies straight to where he means to, filled with confidence and vigor.

Lesson 1: Magnetic Declination

Has the following ever happened to you? You're trying to fly to a particular point. You open the F10 Map and use the ruler tool to measure the bearing and distance between your aircraft and that point. You turn to the bearing you measured, but despite carefully tracking that heading, you still find yourself noticeably off course. There wasn't even any wind in the mission. What happened?​

True vs. Magnetic Heading

The ruler tool in the DCS World Map and Mission Editor gives you True Heading measurements. However, almost all navigation systems display Magnetic Heading (some are toggleable).

The difference between Magnetic Heading and True Heading is due to the difference in location between the Magnetic North Pole (formed by currents of molten iron in the Earth's core, currently located somewhere in Northern Canada) and True North Pole (Santa's House, the point around which the globe spins).

Magnetic Declination

Courtesy of www.magnetic-declination.com

Magnetic Declination is the difference in degrees between the Magnetic North and True North.

• When Magnetic North points East of True North, the sign of the deviation is Positive.
• When Magnetic North points West of True North, the sign of the deviation is Negative.

Note: Do not confuse Declination with Magnetic Variation, which caused by local effects of the airplane's metallic structure on the magnetic compass reading (not simulated in DCS).

How to Find Magnetic Declination

Magnetic Declination can be found on navigation charts. Some DCS modules show you the actual in-game declination either in avionics or on the kneeboard...

• F-14: Kneeboard (Ground Settings, MAG VAR)
• F-16: DED: LIST - 0 MISC - 2 MAGV
• F-18: HSI - DATA - A/C
• AV-8B: Kneeboard (Initial Position: 4. Magvar)
• Mirage-2000: PCN DEC

Magnetic Declination in DCS Maps

Magnetic Declination differs per LOCATION and TIME. The following are "close enough" approximations.

Magnetic Declination per Map in 2016 (Approximate)

• Nevada: +12
• Caucuses: +6
• Syria: +5
• Persian Gulf: +2
• Marianas: +1

Converting True to Magnetic Heading

Source: AFM 51-37 Page 13. Code7700.com

True Heading = Magnetic Heading + Magnetic Declination

Magnetic Heading = True Heading - Declination

Note: If Magnetic Declination is West, remember to use a Negative Sign in the above equations.

Example: Batumi to Kutaisi Flight

It's 2008 and you're on the DCS Caucuses Map. You want to fly from Batumi Airfield to Kutaisi Airfield. The True Bearing measured from the F10 map is 043 degrees. What is the Magnetic Bearing?

1. Magnetic Bearing = True Bearing - Declination
2. Magnetic Bearing = 043 - 6
3. Magnetic Bearing = 037

Bonus: Heading, Bearing, Course, and Track​

• Heading is the direction the airplane's nose is pointed.
• Bearing is the direction between two points.
• Course is very similar to bearing. It's the desired direction you want to fly. If you're flying directly to a point, your course is the same as its bearing.
• Track is actual path the airplane takes across the ground. It's affected by wind and navigational inaccuracies.

Lesson 2: Basic Instrument Navigation

The Goon knows where he is at all times. He knows where he is, because he knows where he isn't...

Horizontal Situation Indicator

Modified from DCS World F-15C Manual by Eagle Dynamics.

The primary navigation instrument of all modern jet aircraft is the Horizontal Situation Indicator (HSI). Pictured is the HSI found on the DCS F-15C Eagle. The HSI on your particular aircraft might look different, but they all have the same features.

1. A rotating compass card that shows your aircraft heading on the top.
2. A bearing pointer that points to your selected navigation target. Be that an INS waypoint, VOR, TACAN, or Sensor Point of Interest (SPI).
3. A range window that shows your distance (in nautical miles or kilometers) from the selected navigation target.
4. An adjustable course needle and course deviation indicator.

For this lesson and subsequent lessons, we will not use the adjustable course needle. The reasons are twofold:

1. Low fidelity modules of the FC3 series do not allow the player to adjust the course to a waypoint.
2. In full fidelity modules, tactical navigation can be performed safely and efficiently without taking hands off flight controls to adjust knobs.

Flying Directly To/From a Point

The most basic navigation tasks consists of flying directly to your destination.

Goofus accepts the bearing pointer by blind faith.

Gallant double checks his avionics, making double-sure he's in the correct navigation mode and has the right waypoint selected.

• To fly to a point, turn so the bearing pointer head is at 12 o'clock on your HSI.
• To fly directly away from a point, turn so the bearing pointer tail is at 12 o'clock on your HSI.

Flying a DME Arc

A DME Arc involves flying a constant-radius circle, or portion of a circle, around a designated point. Tactically, this can be used to anchor your flight over a specific geographical landmark, or to orbit a target to observe it while remaining outside enemy weapons range. This maneuver is also commonly used in instrument procedures.

To Enter a DME Arc:

1. Turn to place the bearing pointer head at either the 3 or 9 o'clock position on your HSI. The exact choice depends on the tactical situation, it may be preferable to put the bearing pointer head on the same side as your targeting pod.
2. Keep turning to maintain the bearing pointer head at 3 or 9 o'clock. Depending on the size of your arc, you may find it easier to keep a continuous bank, or fly short straight segments. To fly short segments: Allow the bearing pointer to drift aft 5-10 degrees behind your 3/9 line. Then turn to place the bearing pointer 5-10 degrees ahead of your 3/9 line and level your wings, allowing the bearing pointer to drift aft again, and repeat.

To Decrease Radius on a DME Arc:

1. Steepen your turn, placing the bearing pointer ahead of the 3/9 line on the HSI.
2. Watch the distance decrease.
3. When you reach the desired distance, turn to place the bearing pointer on the 3/9 line.

To Increase Radius on a DME Arc:

1. Level your wings, allow the bearing pointer to drift behind your 3/9 line on the HSI.
2. Watch the distance increase.
3. When you reach the desired distance, turn to return the bearing pointer to the 3/9 line.

Arcing to a Radial:

A radial describes your position relative to another point, from its perspective. Imagine 360 bicycle spokes coming out from a point in the ground. The spoke pointed due North is the 360 radial, the spoke due East is the 090 radial, and so forth.

Note: Radials can be confusing but they are always numbered by the bearing from a point. For example, if your bearing to a point is 180, you are on its 360 radial.

Intercepting a radial is commonly using in instrument approach procedures to align you with the landing runway. Tactically, it can be used to control the direction from which you attack a target, either due to geographical constraints (i.e. the target is in a valley running North-South) or due to the presence of nearby friendly forces.

Tip: The bearing pointer tail always points to the radial you are on.

To Intercept a Radial Inbound:

1. Arc until the bearing pointer tail reaches the desired radial.
2. Turn directly to the waypoint.

Intercepting a Course

Intercepting a specific course to or from a fix is almost identical to intercepting a radial. Observant pilots would notice that when flying straight, the bearing to a fix will always slowly move towards the rear of the aircraft as you fly past it. Hence, the saying "The Head Always Falls". Conversely, the opposite is true for the tail of the bearing pointer "The Tail Always Rises."

Example 1

You are on the 270 radial, directly inbound. You wish to intercept the 130 radial inbound.

1. See that the desired course of 130 is to the right of the current bearing 090.
2. Turn left so the Bearing Pointer is on the same side as the desired course.
3. Wait for the head of the bearing pointer to drop to the desired course. The Head Always Falls.
4. Turn inbound.